DJI Inspire 2 Top Camera Mount For -GoPro-Fusion-Sequoia-FLIR

Description

TOP Mount a FLIR VUE , Sequoia Multi spectral or any type of GoPro style
auxiliary camera  like a 360 Fusion or MAX on TOP of your DJI Inspire 2 series .
This is link to all the installation manuals if you want see what is required:
https://drive.google.com/drive/folders/1aLXQQyOWpJ5DUHn5p3Vz3EXyEwhk8yO-?usp=sharing
DJI Inspire DRONE NOT INCLUDED IN AUCTION
Weights:
Top Mounts I1 or I2 50-56g
Bottom Mounts I1 ro i2 15-20g
Typical mounting with fasteners for 1 device 6-10g
SAMPLE VIDEO 11/03/19
Top Mount Maximum Forward Position
Link to video showing GoPro Fusion 360 stability tests
https://www.youtube.com/watch?v=WzYEDYvChhU
SAMPLE VIDEO 11/03/19
Top Mount Maximum Rearward Position
Link to video showing GoPro Fusion 360 stability tests
https://www.youtube.com/watch?v=6RHKTFD20HM&t=83s
This is for top mounting on a DJI Inspire 2
1-Includes adaptor to accept any GoPro style mounting buckle (see photos)
(watch the video for stability tests in two positions above links)
2- Includes front drop down GoPro adaptor for lighting or other accessory (see photos)
3- Includes GoPro Shorty Grip adaptor (see photos)
4- If you need a power pak for camera such as FLIR VUE or Parrot Sequia it can be attached to the top mount which has 6 inches of mounting area or you can add one of Rear Bottom Mounts for attachment.
Adaptors for Parrot Sequoia and Flir VUE included
Sequoia requires a top and bottom mount since it has a camera and sunlight component
5- We offer a optional mounting frame for the EVO SS when used with the GoPro Hero 8 Black search for
EVO SS GoPro HERO8 BLACK Mounting Kit Dual Position
on Ebay
Mount is bolted into frame and requires no modification all stainless steel attachment hardware included. Manufactured out of high grade PLA
This mount is not a
replacement
for the standrad DJI front mount camera however you could use as your only camera if you do not have a front camera.
(Custom mounting available send requirements for review) We have adaptors for Sequia and Flir VUE in the works.
COPYRIGHT © 2019 alienconcepts incorporated
Multiple units are available
MADE IN THE USA
General for All Mounts
We are constantly updating based on field use reports . As a result photos and instructions and components may change
at any time.
Disclaimer
We offer no guarantees  that a mount will perform up to your expectations since there are too many variables.
Use best practices for safe flying at all times . If unsure check with the FAA drone rules and regulations online.
We assume no responsibility for any damage or injury because of the addition of one of our mounts.
Payload Location and Clearance
When mounting payloads verify against recommended weights and sizes for your drone in manual or
contact manufacturer
If you mount anything on top of the mount make sure it has prop clearance a simple checking method is listed next:
1-Place you DJI Inspire 1 or 2 in travel model with props on and look down from directly above make sure
you have clearance with nothing protruding outside of the drone main body envelope into prop space
2-If you do have payloads in the body envelope or you are unsure make styrofoam size model and affix it with double stick
or velcro. Manually move the jack screw through its full range and make sure there is no interference with the props.
Safeguards
Use a safety lanyard on your mounts. This is one I use : Amazon
MIZUGIWA Stainless Steel Lanyard Cable Tether Safety Wire for Loss Prevention 2 Loops w/Quick Release Ring & Rubber Coating 12" Set of 10